avrdude.exe: Version 5.11, compiled on Sep 2 2011 at 19:38:36 Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/ Copyright (c) 2007-2009 Joerg Wunsch System wide configuration file is "hardware/tools/avr/etc/avrdude.conf" Using Port : lpt1 Using Programmer : usbtiny Overriding Baud Rate : 19200 avrdude: usbdev_open(): Found USBtinyISP, bus:device: bus-0:\\.\libusb0-0001--0x1781-0x0c9f AVR Part : ATMEGA328P Chip Erase delay : 9000 us PAGEL : PD7 BS2 : PC2 RESET disposition : dedicated RETRY pulse : SCK serial program mode : yes parallel program mode : yes Timeout : 200 StabDelay : 100 CmdexeDelay : 25 SyncLoops : 32 ByteDelay : 0 PollIndex : 3 PollValue : 0x53 Memory Detail : Block Poll Page Polled Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- --------- eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00 hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00 efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00 lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00 calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00 signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00 Programmer Type : USBtiny Description : USBtiny simple USB programmer, http://www.ladyada.net/make/usbtinyisp/ avrdude.exe: programmer operation not supported avrdude.exe: Using SCK period of 10 usec avrdude.exe: AVR device initialized and ready to accept instructions Reading | ################################################## | 100% 0.02s avrdude.exe: Device signature = 0x1e950f avrdude.exe: safemode: lfuse reads as FF avrdude.exe: safemode: hfuse reads as DA avrdude.exe: safemode: efuse reads as 5 avrdude.exe: erasing chip avrdude.exe: Using SCK period of 10 usec avrdude.exe: reading input file "hardware/arduino/bootloaders/optiboot/optiboot_atmega328.hex" avrdude.exe: input file hardware/arduino/bootloaders/optiboot/optiboot_atmega328.hex auto detected as Intel Hex avrdude.exe: writing flash (32768 bytes): Writing | ################################################## | 100% 19.58s avrdude.exe: 32768 bytes of flash written avrdude.exe: verifying flash memory against hardware/arduino/bootloaders/optiboot/optiboot_atmega328.hex: avrdude.exe: load data flash data from input file hardware/arduino/bootloaders/optiboot/optiboot_atmega328.hex: avrdude.exe: input file hardware/arduino/bootloaders/optiboot/optiboot_atmega328.hex auto detected as Intel Hex avrdude.exe: input file hardware/arduino/bootloaders/optiboot/optiboot_atmega328.hex contains 32768 bytes avrdude.exe: reading on-chip flash data: Reading | ################################################## | 100% 17.54s avrdude.exe: verifying ... avrdude.exe: 32768 bytes of flash verified avrdude.exe: reading input file "0x0F" avrdude.exe: writing lock (1 bytes): Writing | ################################################## | 100% 0.02s avrdude.exe: 1 bytes of lock written avrdude.exe: verifying lock memory against 0x0F: avrdude.exe: load data lock data from input file 0x0F: avrdude.exe: input file 0x0F contains 1 bytes avrdude.exe: reading on-chip lock data: Reading | ################################################## | 100% 0.00s avrdude.exe: verifying ... avrdude.exe: 1 bytes of lock verified avrdude.exe: safemode: lfuse reads as FF avrdude.exe: safemode: hfuse reads as DA avrdude.exe: safemode: efuse reads as 5 avrdude.exe: safemode: Fuses OK avrdude.exe done. Thank you.